AtermらくらくQRスタート for Android 2.0.13 Apk
Rate saved, Thank!
3.5 (1 votes)
Description of AtermらくらくQRスタート for Android
By reading the product attach a "Wi-Fi settings for QR Code" in the app, Wi-Fi connection settings of smartphone-tablet and Aterm series base unit you can easily.
"Wi-Fi settings for the QR code" is the information of the network name (SSID) and encryption key (password) is encrypted, the operation is not only easy, it is conscious security.
Aterm product that corresponds to the "Easy QR Start 2" function, Wi-Fi connection and the Internet connection settings can be done in the app.
[Corresponding version]
· Android 4.1 or more (corresponding to the Google Play, available in a smartphone-tablet terminal that corresponds to the camera function)
Detailed correspondence version, please check the AtermStation (http://121ware.com/product/atermstation/special/rakuraku_qr/index.html).
[Connection confirmation models]
Connection confirmation smartphone tablet terminal, Aterm series compatible models, please check the AtermStation (http://121ware.com/product/atermstation/special/rakuraku_qr/page3.html).
【Notes】
- Should be used to read "Wi-Fi settings for QR Code" is made to the accompanying location will differ depending on the product. Please check the attached location in the user's manual of each product.
- And auto-focus function is not the camera, in a low-resolution camera, you may QR code can not be recognized.
Smartphone or if you are using the zoom feature of the tablet, the display of the QR code reading frame of the camera view in the screen, you may deviate from the center of the screen. Please run this app again return to the normal display.
• If the QR code is difficult to read in your use of the terminal of the camera, please try the following.
To adjust the position of the camera so as to be perpendicular to the -QR code.
- Adjust so that the ceiling lamp or the like is not glare in the QR code at the time of reading.
- To read in bright places. (Too bright location out of direct sunlight, etc. Avoid)
· Aterm of SSID, encryption keys can be set in the state of the initial value. Can not be set and have been changed from the initial value.
- Please make sure that prior to Aterm of firmware to be connected is up to date. Please been upgraded if it is not up to date.
And products is the handset mode, if you are operating in a repeater mode can not be set.
• If the QR code can not download or if applications that can not be recognized, please do manually Wi-Fi settings from the smartphone-tablet. Please refer to the manual of Aterm detailed setting method.
○ "Easy QR Start 2" only
In the case of · PPPoE router mode, you must enter the ID / password.
• If the Internet connection settings in the setting of PPPoE, until all of the configuration is complete, it may take about 10 minutes.
• The Internet connection settings at the time, if it detects a conflict of IP address, it may fail to set. If this is the case, please do the settings in the WEB setting screen of Aterm.
• If you have changed the settings, please review the configuration information. Or Aterm to initialize, please run the app again to return to the factory settings.
- In an environment where connection configured other access points are nearby, you may fail to set. If this is the case, please turn off the power of the access point other than Aterm to be set.
Bridge mode, the access point mode, the router of a multi-stage connection, the Internet connection settings can not be performed correctly (Wi-Fi settings can be done).
- When it is contact us by e-mail, so that the "[email protected]" it is possible to receive, to be the filtering settings you use e-mail, thank you. In addition, the inquiry other than this app, please be advised that it may not be able to answer.
※ QR Code is a registered trademark of DENSO WAVE INCORPORATED.
※ This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit.
new function
· Ver2.0.13 Improved administrator password entry screen.
You changed the error message.
Added support for · Ver2.0.12 Android 6.
· Ver2.0.11 was changed the company name display (NEC Access Technica -> NEC platform's).
Improved the SSID display.
· Ver2.0.10 was shorten the set time in the part of the Internet connection settings function.
We strengthened our Internet connection test with WiMAX mobile router.
· Ver2.0.9 Added Internet connection setting function ( "Easy QR Start 2" function enabled Aterm product is the subject).
· Ver2.0.8 Improved screen display on the part of the Android terminal.
You do not want to see the contents of the wireless LAN configuration information you do not want to use with the new QR code.
· Ver2.0.4 has been supported in the new QR code version.
· Ver1.1.0 Improved installation issues in the part of the Android terminal.