QUPiO Plus歩数計 1.7.0 Apk

● It is an application for the user of WEB service "QUPiO Plus".    This service is only available to users of the web service "QUPiO Plus".    Android 5 or higher is the recommended environment. In addition, the operation is not guaranteed for tablets. ● Easy to measure daily steps!   You can measure your daily steps with your smartphone (Android). ● Data linkage with WEB service "QUPiO Plus"! If you log in to the web service "QUPiO Plus" in the app "QUPiO pedometer app", step count data measured by "QUPiO pedometer app" is registered when the app screen is opened to the web service "QUPiO Plus" You [Initial setting method] 1. Launch the application and display the application screen. 2. Please confirm the terms of use and proceed from the "Agree" to the next step. 3. Set your login ID (email address) and password in the web service "QUPiO Plus" and press "Configure with the above." ※Notes The data is linked to the web service "QUPiO Plus" at the timing when the application is started and the screen is displayed. Since automatic communication is not performed when the screen is not displayed, it is recommended to display the application screen once a day. "QUPiO" has been renewed as "QUPiO Plus" since April 1, 2019. If you are using version 1.6 or less of the Pedometer application, you can not communicate to "QUPiO Plus". Please update to the latest version. Be sure to start the pedometer application when powering off or restarting. Step count can not be performed unless it is started. (About Andorid's step sensor) This application uses the hardware sensor value held by the smartphone by default. However, accuracy may not be obtained by hardware measurement. If the accuracy is not obtained with the hardware sensor method, switch to the "original method" in the "setting menu" and use it, check the accuracy, and check the one with the higher accuracy. (Energy saving function) Energy saving setting is enabled by default on Android 6 or later OS. If the energy saving function is enabled, the operation of the app is limited and measurement of the number of steps does not work well. After checking the energy saving function, please set "disabled" for the QUPiO Plus pedometer application. Also, if you have installed a power saving application, please "remove this application from the power saving target". Some models require a special specification (such as OPPO) to maintain the startup status. Please check the manual of your smartphone and make sure that the pedometer application being activated is not disabled. If your model has a setting to allow automatic startup, please set that as well. Pedometer application There is also a case where it is excluded from the target, though it has been excluded from the target, if it has been excluded from the target, if it is not "new application" and "update of the application". If the step count does not count well after updating, please check the settings again. * Notes for Galaxy users Galaxy has a feature called "power saving the application". This is a function that "runs the application that does not use for 3 days or more with power saving". If it becomes the target of this power saving, the app will stop during sleep and you will not be able to count steps. In order to cancel this, 1. Open the "Battery" setting 2. Press the "Details" button in "Power saving the application" 3. Find "QUPiO Plus Pedometer" from the list 4. Tap to select "Disable" Please do the operation. * Attention to those using Zenfone If "automatic startup is not permitted" in the auto-start manager, steps can not be counted successfully because the terminal can not start automatically when restarted. Be sure to allow it. * Notes for Xperia users Applications are disabled when the device is not in use or when the application is not used for several days to reduce battery consumption per application. Display the battery screen with Apps> Settings> Battery, tap Menu> Battery Optimization> Apps / Others> No Battery Optimization / Applications / Features Please check if the QUPiO + pedometer is set to "do not optimize". If optimized, steps can not be counted properly. * Note to users of Y mobile! There is a model that contains Yahoo! Smartphone optimization tool as an installed application. If the operation is strange, please check the following settings. When the "Auto Power Saving" tab is turned on, the settings in the lower right-Automatic stop prohibition application settings ~ ~ When power saving is in progress, an application that you do not want to automatically exit while the screen is locked So that "QUPiO pedometer" application is specified from the list of running applications. * Notes for HUAWEI Honor 6 Plus users There is a setting item in the place different from power related called "Privacy and Security" of the setting screen of Android. There is an item called "protected apps", and the list of apps is displayed in it. If you switch on the "high power consumption" here, the app will not end even when the liquid crystal is turned off. Because the pedometer application must detect all vibrations when walking, the correct number of steps can not be counted unless the operation is continued even when the liquid crystal is off. Please acknowledge your setting. * For users of OPPO models ・ Please select QUPiO Plus pedometer in "app management" of setting menu ・ Check the permission of automatic start and allow it ・ Click Power Consumption Protection setting and click "Allow background execution" ・ When QUPiO Plus Pedometer starts, click □ button at the bottom of the screen to display the start application list, swipe down with 3 fingers on QUPiO + Pedometer screen, and click lock icon. This will prevent the app from closing automatically. (Cooperation of steps) If you can not communicate step-by-step communication by opening the application and open the screen, perform "Step-by-step data synchronization" in the menu and check if it is registered in the web service "QUPiO". If synchronization does not work here, please login again and then check the synchronization. (Step measurement at lock and sleep) Depending on the model you use, even though the energy saving setting has been canceled, the measurement function (sensor) may not operate during lock or sleep, and you may not be able to count steps. This is a device-specific specification, not a bug on this application. Please be aware in advance.